FLASHER UTILITY BY SKIPFIE. TO BE USED WITH SKIPPAD. COM4 Status for device COM4: ----------------------- Baud: 1200 Parity: None Data Bits: 8 Stop Bits: 1 Timeout: OFF XON/XOFF: OFF CTS handshaking: OFF DSR handshaking: OFF DSR sensitivity: OFF DTR circuit: OFF RTS circuit: ON WAITING 3 SECONDS FOR SKIPPAD TO RECONNECT COM6 avrdude.exe: Version 6.3, compiled on Jan 17 2017 at 12:00:53 Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/ Copyright (c) 2007-2014 Joerg Wunsch System wide configuration file is "./avrdude.conf" Using Port : COM6 Using Programmer : avr109 Overriding Baud Rate : 57600 AVR Part : ATmega32U4 Chip Erase delay : 9000 us PAGEL : PD7 BS2 : PA0 RESET disposition : dedicated RETRY pulse : SCK serial program mode : yes parallel program mode : yes Timeout : 200 StabDelay : 100 CmdexeDelay : 25 SyncLoops : 32 ByteDelay : 0 PollIndex : 3 PollValue : 0x53 Memory Detail : Block Poll Page Polled Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- --------- eeprom 65 20 4 0 no 1024 4 0 9000 9000 0x00 0x00 flash 65 6 128 0 yes 32768 128 256 4500 4500 0x00 0x00 lfuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00 hfuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00 efuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00 lock 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00 calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00 signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00 Programmer Type : butterfly Description : Atmel AppNote AVR109 Boot Loader Connecting to programmer: . Found programmer: Id = "CATERIN"; type = S Software Version = 1.0; No Hardware Version given. Programmer supports auto addr increment. Programmer supports buffered memory access with buffersize=128 bytes. Programmer supports the following devices: Device code: 0x44 avrdude.exe: devcode selected: 0x44 avrdude.exe: AVR device initialized and ready to accept instructions Reading | ################################################## | 100% 0.00s avrdude.exe: Device signature = 0x1e9587 (probably m32u4) avrdude.exe: safemode: hfuse reads as D8 avrdude.exe: safemode: efuse reads as CB avrdude.exe: reading input file "./firmware.hex" avrdude.exe: input file ./firmware.hex auto detected as Intel Hex avrdude.exe: writing flash (12934 bytes): Writing | ################################################## | 100% 1.00s avrdude.exe: 12934 bytes of flash written avrdude.exe: safemode: hfuse reads as D8 avrdude.exe: safemode: efuse reads as CB avrdude.exe: safemode: Fuses OK (E:CB, H:D8, L:FF) avrdude.exe done. Thank you. FIRMWARE UPDATED. ECHO is off. DONE, CHECK IF IT HAS UPDATED PROPERLY IN LOG.TXT! EXIT NOW! Press any key to continue . . .